HALLOWEEN MASON JARS with Wooden Pumpkin Spoons

Hey ya'll!

Here's a Halloween themed idea for those plain ole' Mason jars you may have.  And if you don't have any on hand, Walmart and even the Dollar General stores carry them in cases.

Plain jar before

The Halloween themed Mason jar looks like it has a lot going on. Really it was pretty simple.

Okay, so first off we need to clean the outside of the jar with a little bit of alcohol.  This will remove all dust, lint and crap so it will have a good, sharp finish.

I just wiped it down with a paper towel dipped in the alcohol.

Okay then just paint the inside of the jar a color you want to pop. I choose the Cinnamon color from Folk Art craft paints.  

Oops, this is a pic of another one I painted Cinnamon on the outside. But anyways, just paint the orange on the inside if you are going for the look of my top pic, or vice versa if for another. 

And for the outside I went with antique white.

 

Okay, I've switched up the pics somehow of the inside and outside, but this pic shows the white inside. But remember you want the white on the outside if you want it like the jar at the top of this page.

For some reason I've vice-versa'd the pics.

Okay, anyways, after you have painted a good coat on the outside in white, and its dry, take some fine grit sandpaper and sand it. 

And you'll start seeing this.

I like all the scratchy type marks.

And wipe all the dust off then add one coat of sealer. I like the varnish in satin.

And let it dry then decorate it with burlap strips, a bell

                         

      and some of my pre-made  

Halloween Themed Wooden Spoons.

And here it is finished:

And here's the other one I just finished up.

See ya'll next time,

-Lisa

You may also like:

Halloween themed Mason jars with Pumpkin magnets

And Halloween Pumpkin and Ghost Wooden Spoons

DIY Photo Necklace

DIY Photo Necklace

Snowmen Light bulb Ornaments

I don't think I've previously written about these adorable snowmen Ornaments.
If I have sorry, but they are just so dang cute they need to be posted again! lol

I have taken both new and vintage Christmas tree glass bulbs and painted them up as snowmen.

Their sizes are approximately:

Height: 3 Inches; Width: 1.5 Inches; Depth: 1 Inches

I have hand painted each Christmas bulbs with various Snowmen faces and expressions and then attached craft wire for easy hanging.

These are best displayed as a set. So I tend to make a lot of them to sale.
A tree full of these would look awesome.

I do hand paint new ones each week, so no two are ever exactly alike. And that is a bonus

to making hand made gifts. Each and every one is unique.

Great to decorate with or to give as gifts separately. 

And adorable as cute tie on gifts to top wrapped gifts with.

If you have any old bulbs on a strand that don't burn anymore give this a try.
You can also buy brand new bulbs, this size in packages of 5 at Walmart and Lowes.

Happy Crafting!

Personalized Christmas Ornaments and Keychains

The first day of December here brings new projects for Christmas. 

And I woke early to get a head start on them.

Since time is short, I will just include a few photos of what is keeping me busy today and for the next few weeks.

I hope it may give you some ideas on personalized ornaments you could make.

Not only by just engraving them but by painting.

And I just have to include these little babies feet badge ID clips I've been making.

And these were a few engraved wooden spoons from Halloween I didn't get around to posting.

DIY Concrete Pumpkins

DIY CONCRETE PUMPKINS

Hey Ya'll!

Ready to make some concrete pumpkins for Halloween?

I sure am even though it is September 5th.  I've been ready for a few weeks now.

I made these two pumpkins for just about $4.00 each.

And they weigh approximately 25 pounds each!

This is a very simple and inexpensive process, so don't worry much about messing up.

Here's what you will need:

- A 50 pound bag of Quickrete $5.00 (I got from Lowes) Makes 2 pumpkins

-Pam cooking spray or Generic brand like I used "Chef's Own $1.00

-2 Plastic Pumpkins $1.00 each

-Mixing bucket

-Water

-Sharp utility knife

-

.

I didn't have any plastic pumpkins on hand from last Halloween so I first looked around at the local Goodwill.  There I found three of them for only .99cents each.   Sad only because new at Walmart they were 1.00 each. lol. So even though super cheap, I just figured they'd be cheaper for some reason.

Here is a photo of most of my supplies.  Notice there are three pumpkins I had ready.

Well, I found out quick that a 50 pound bag of Quickrete concrete mix only makes 2 pumpkins!

Yes that's right.  So each pumpkin after done will be approximately 25 pounds right?

I used an old Lowes plastic 5 gallon utility bucket for mixing the concrete in.

Here's my trick. Since the bag is so heavy and awkward to handle, I sit it on the back of my truck's tailgate.  Then I slit a whole into the bottom, corner of the bag and let it freely pour directly into my bucket.

This is so much easier than handling the bag so many times, adding a touch more and so.

Don't mix it too runny!  Read your bag for best instructions.

Here is a very important part!

Right before you begin to pour your concrete mix into your pumpkins, 

YOU MUST SPRAY THE INSIDES GOOD 

with a coat of the PAM or Generic cooking spray.

This will coat the insides and allow the concrete to release easier later on after drying.

I used a plastic, kids shovel I had on hand for dipping the concrete out and into the pumpkin.

I tried to keep it from coming out.

But it was hard because after you fill up your pumpkin, 

you must keep lifting it up and tapping it down on the ground 

to release any air bubbles trapped inside.

Do this over and over a few times.

You can always take your hand or cloth and wipe away the excess right at the rim.

Now comes the hard part.....

You must let them sit for about 24 hours before you start to cut the plastic buckets.

This is how I made my cuts.

I did four slices, top to bottom very carefully.

Try to avoid cutting so deep that it marks the concrete.

The concrete of mine, was still not completely set up even after 24 hours.

And then you slowly peel them back.

And then the concrete pumpkin will finally begin to emerge completely out of the plastic.

And this is it.

This is my very first try at making a Concrete Pumpkin.

I did let them sit another 24 hours after getting them out of the plastic before handling them too much.

You can see the holes in the concrete where air was apparently still trapped.

But for my purposes they are just fine.

I've read about a countertop mix available at Lowes that allows for a super smooth finish.

But for me just wanting them to sit outside as decoration, I don't want to add anything to the mix to make it very expensive.

Here are the plastic buckets after I got the concrete out.

And here it is after it was all complete.

I like the concrete look but on the next one I may do a white, crackle paint finish.